Experimental Investigation of Residual Stress Measurement on Cold Roll Bonded Al/Cu Composite by Incremental Hole-Drilling Method

Document Type : Research Article

Authors

Faculty of Mechanical Engineering, University of Kashan, 8731753153, Kashan, Iran

Abstract

Hole drilling is a semi-destructive procedure used to measure residual stress. This type of stress, caused by mechanical and thermal effects, can significantly impact the lifetime of composite specimens. This paper studies the residual stress measurement on aluminum-copper composite specimens. The experimental procedure involved creating five different composite specimens using a rolling machine, and then using ABAQUS software in FEA analysis to calculate the calibration coefficients. The American standard ASTM E837 was used to determine the residual stress measurement. The specimens are manufactured through the Cold Roll Bonding (CRB) process with a rolling machine. The incremental hole-drilling strain gauge method was used, with the MTS-3000 Restan machine, to measure the residual stresses. The aluminum-copper composite specimens were manufactured in different sequences. The results showed that the ultimate tensile strength of aluminum mono-layer was lower than all composite specimens. On the other hand, the ultimate tensile strength of the copper mono-layer was higher than all samples, except rolled Cu-Cu one. Furthermore, a comparison between two-layer and three-layer composite specimens showed that the two-layer specimen stored more residual stress. In general, copper metal has stored more residual stress than aluminum metal.

Keywords

Main Subjects


[1]   Schajer G. S., 1988. Measurement of Non-Uniform Residual Stresses Using the Hole-Drilling Method. Part I—Stress Calculation Procedures. Journal of Engineering Materials and Technology, 110(4). pp. 338–343.
[2]   Sedighi M., Honarpisheh M., 2012. Investigation of cold rolling influence on near surface residual stress distribution in explosive welded multilayer. Strength Mater, 44, pp. 693-698.
[3]   James M. N., Hattingh D. G., Asquith D., Newby M., Doubell P., 2016. Applications of Residual Stress in Combatting Fatigue and Fracture. Procedia Structural Integrity, 2, pp. 11–25.
[4]   ASTM E837-20, 2023. Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method.  https://www.astm.org/e0837-13a.html.
[5]   Ma Y., Yao X., Zhang D., 2015. Axially symmetrical stress measurement in the cylindrical tube using DIC with hole drilling. Optics and Lasers in Engineering, 66, pp. 174–180.
[6]   Chen H., Song Y., Chen X., Yu X., Chen S., 2020. In situ studies of full-field residual stress mapping of SS304 stainless steel welds using DIC. Int J Adv Manuf Technol, 109(1), pp. 45–55.
[7]   Babaeeian M., Mohammadimehr M., 2021. Experimental and computational analyses on residual stress of composite plate using DIC and Hole-drilling methods based on Mohr’s circle and considering the time effect. Optics and Lasers in Engineering, 137, p. 106355.
[8]   Babaeeian M., Mohammadimehr M., 2020. Investigation of the time elapsed effect on residual stress measurement in a composite plate by DIC method. Optics and Lasers in Engineering, 128, p. 106002.
[9]   Steinzig M., Upshaw D., Rasty J., 2014. Influence of Drilling Parameters on the Accuracy of Hole-drilling Residual Stress Measurements. Exp Mech, 54(9), pp. 1537–1543.
[10] Blödorn R., Viotti M. R., Schroeter R. B., Albertazzi A., 2015. Analysis of Blind-Holes Applied in the Hole-Drilling Method for Residual Stress Measurements. Exp Mech, 55(9), pp. 1745–1756.
[11] Rickert T., 2016. Residual Stress Measurement by ESPI Hole-Drilling. Procedia CIRP, 45, pp. 203–206.
[12] Bonnet C., Pottier T., Landon Y., 2021. Development of a multi-scale and coupled cutting model for the drilling of Ti-6Al-4V. CIRP Journal of Manufacturing Science and Technology, 35, pp. 526–540.
[13] Shi X., Hussain G., Butt S. I., Song F., Huang D., Liu Y., 2017. The state of residual stresses in the Cu/Steel bonded laminates after ISF deformation: An experimental analysis. Journal of Manufacturing Processes, 30, pp. 14–26.
[14] Sedighi M., Honarpisheh M., 2012. Experimental study of through-depth residual stress in explosive welded Al–Cu–Al multilayer. Mater Des, 37, pp. 577–581.
[15] Alinaghian M., Alinaghian I., Honarpisheh M., 2019. Residual stress measurement of single point incremental formed Al/Cu bimetal using the incremental hole-drilling method. International Journal of Lightweight Materials and Manufacture, 2(2), pp. 131–139.
[16] Tamonov A. V., Sumin V. V., 2004. Investigation of Residual Stresses in a Bimetallic Stainless Steel–Zirconium Adapter by Neutron Diffraction. Journal of Neutron Research, 12(1–3), pp. 69–73.
[17] Varavallo R., Moreira M., Paes V., Brito P., Olivas J., Pinto H. C., 2014. Microstructure and Residual Stress Analysis of Explosion Cladded Inconel 625 and ASME SA516-70 Carbon Steel Bimetal Plates. Advanced Materials Research, 996, pp. 494–499.
[18] Fronczek D. M., et al., 2018. Residual stress distribution, correlated with bending tests, within explosively welded Ti gr. 2/A1050 bimetals. Materials Characterization, 144, pp. 461–468.
[19] Kotobi M., Honarpisheh M., 2018. Through-depth residual stress measurement of laser-bent steel–titanium bimetal sheets. The Journal of Strain Analysis for Engineering Design, 53(3), pp. 130–140.
[20] Kotobi M., Mansouri H., Honarpisheh M., 2019. Investigation of laser bending parameters on the residual stress and bending angle of St-Ti bimetal using FEM and neural network. Optics & Laser Technology, 116, pp. 265–275.
[21] Dong F., Yi Y., Huang S., 2020. Measuring internal residual stress in Al-Cu alloy forgings by crack compliance method with optimized parameters. J. Cent. South Univ., 27(11), pp. 3163–3174.
[22] Xie W., Tomiko Y., Kazumasa K., 2012. Formation of Intermetallic Compounds on the Bond Interface of Aluminum-Clad Copper and its Influence on Bond Tensile Strength. Applied Mechanics and Materials, 117, pp. 984–989.
[23] Mao Z., Xie J., Wang A., Wang W., Ma D., Liu P., 2020. Effects of annealing temperature on the interfacial microstructure and bonding strength of Cu/Al clad sheets produced by twin-roll casting and rolling. Journal of Materials Processing Technology, 285, p. 116804.
[24] Biyik S., 2018. Effect of Reinforcement Ratio on Physical and Mechanical Properties of Cu-W Composites Synthesized by Ball Milling. Materials Focus, 7(4), pp. 535–541.
[25] Jamaati R., Toroghinejad M. R., 2011. Cold roll bonding bond strengths. Materials Science and Technology, 27(7), pp. 1101–1108.
[26] ASTM E8/E8M-22., 2024. Standard Test Methods for Tension Testing of Metallic Materials. https://store.astm.org/e0008_e0008m-22.html.
[27] ASTM E837-20., 2021. Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method. https://store.astm.org/e0837-20.html.
[28] Niku-Lari A., Lu J., Flavenot F., 1985. Measurement of residual-stress distribution by the incremental hole-drilling method. Journal of Mechanical Working Technology, 11(2), pp. 167–188.